Posts Tagged ‘shopmade’

I like old tools.  My favorite old tools to collect and rehabilitate are probably hand planes.  With hand planes, having a Cap Screw Screwdriver comes in handy for a properly fitted driver to adjust the plane iron cap screw.

Online retailers sell their version of these little tools for upwards of $20.  I decided to make mine from some of the things I had laying around the shop.

Here are the two versions of the Cap Screw Screwdriver I made.  One is hooded; the ferrule extends the length of and surrounds the blade.  The other has an exposed blade.  Both have turned hard maple doorknob style handles that fit nicely in the palm of the hand.  {I apologize now that this blog post is picture heavy.}

DSCN2155

In this blog, I will walk through the process of making the hooded version of the cap screw screwdriver.  The exposed blade version follows a similar process.  I will include notes with some of the differences when making the two versions.

I selected a 11/16” spade drill bit to make the blades for both drivers.  I marked a line across using a permanent ink marker to indicate where I will cut the bit to make the two blades.  The point section will be used to make the blade for the hooded version and the shaft section will be used for the exposed blade version.  Note: I also marked a line on the shaft where I will cut it for the exposed blade driver.

DSCN2095

A Dremel tool with a diamond wheel makes nice work of cutting the spade bit.  After cutting, we have the blanks for both driver blades.

DSCN2096DSCN2097

The spade bit is slightly thicker than the width of the cap screw slot.  A few seconds at the belt sander works nicely to thin the blade to the necessary thickness.  Be careful not to let the blade get too hot while sanding.  We do not want to lose the temper in the steel.

DSCN2100

Check to confirm a nice snug, but not too tight fit.

DSCN2101

Selected and trimmed hard maple blank for both drivers.  This blanks is just over 2” square and approximately 7 ½” long.  We will make both handles from this blank.

DSCN2102

Check each blade with my drill index to find the appropriate sized hold for each.  The hooded driver (point blade) will need a ¼” hole.  The exposed blade (shaft end) will need a 9/32” hole.

DSCN2098

Mark the center and drill ¼” hole, approximately 1” deep for the hooded blade.  We will use this center drilled hole to index out live center on the lathe.

DSCN2103

Using a four jaw chuck to secure the blanks and a 60 degree live center, indexed in the hole we just drilled.  Rough turn the blank round.

DSCN2104DSCN2105

Mark a pencil line approximately middle of the blank.  Use a thin parting tool, to mark the divide between the two handle blanks.  We will turn from the live center back to this dividing line for our first driver.

DSCN2106DSCN2107DSCN2108

Mark the length for to turn our tenon.  We will turn the tenon to ¾” diameter to the length indicated.

DSCN2110

Instead of a caliper, I used an open end ¾” to help size the tenon.

DSCN2112

Next, we will remover the blank and clamp in the bench vice so we can cut a slot through center of the tenon for the blade to fit into.  I used one of the pencil marks from when we found the center of the blank as a guide for cutting the slot.

Before removing the blank from the chuck, I marked one side with the jaw number, so I can make sure to return it to the same orientation after cutting the slot.

DSCN2113DSCN2114

Test fit the blade, using a soft mallet to seat it firmly in place.  Remove the blade and return the blank to the lathe.  I marked two lines to indicate the length to extend the tenon and turn a shoulder to transition to the handle.

DSCN2115DSCN2116

We will be using a piece of ¾” copper pipe for our ferrule.  After turning the tennon to the desired length, mark the pipe for the desired ferrule length.  This ferrule will extend the full length of the blade.  For the exposed blade screwdriver, mark the ferrule the same length as the tenon.

DSCN2117DSCN2119

Let’s go ahead and turn down the shoulder to remove some of the material out of our way so we can polish the copper ferrule, we just cut.

DSCN2118

The ferrule should fit snug on the tenon.  Using 1500 grit sand paper, remove any scratches and markings from the copper pipe.  After sanding, I polished with jeweler’s rouge polish.  Then removed the ferrule and set aside to finish turning the handle.  (Be careful.  Ferrule may be hot after polishing.)

DSCN2120DSCN2121

Now we will begin turning the handle to our desired shape.  We are only roughing in the design here.  We will part this handle before finish turning.

DSCN2122DSCN2123

Found a hidden crack in the middle of our handle blank.  It should not interfere with the function of our driver, so I will fill it with a little thin CA glue and wood shavings, then finish turning.

DSCN2124DSCN2125

Decided the original marked length was a little much for our handle.  Turn down the hand to its rough form, then part off the material for our first handle.

DSCN2126

Looks like our little fissure runs through our blank.  This driver is not intended to endure much force, so this fissure should not present a problem with our finished driver.  We will fill it with some thin CA and turning dust, then return to the lathe.

DSCN2127

Switched over to a collet chuck with a ¾” collet.  Our tenon fits nicely in the ¾” collet and is tightly secured in the chuck for final turning and sanding.  Sanded from 100 grit through 220 grit, then using a wire burned a line for added decoration.  After burning our line, I we return to sanding from 22 grit through 400 grit sand paper.

DSCN2128DSCN2129DSCN2130

Finished by applying friction polish, using a soft cloth.  Use the lathe to turn our handle creating the speed needed to create friction and build the desired level of polish.

DSCN2131DSCN2132

I like marking my shop built tools by inlaying a penny for the current year.  This gives me a historical reminder of the year the tool is made.  Rough up the underside of the penny with some 80 grit sand paper.  A drop of medium CA glue will secure the penny in our inlay.  By the way, a United States penny is ¾” in diameter, so a ¾” forstner bit is perfect for this inlay.

DSCN2135DSCN2136

Now, it is back to the work bench to insert the blade in the handle.  A few drops of medium CA glue in the center hole will help secure the blade.  A soft mallet provides enough persuasion to seat the blade completely.

DSCN2138

A little five minute epoxy on the tenon will secure the ferrule in place.  The epoxy gives us enough time to work the ferrule around and make sure we have complete coverage with the epoxy.  Clean off any excess epoxy then allow the epoxy to cure.  Be sure to clean any epoxy off the tip of the blade.

DSCN2139

This beautiful tool is ready to go to work.

DSCN2140DSCN2141DSCN2143DSCN2145

The process to make the exposed blade version of this tool is similar, so I won’t waste your time with the step-by-step.

DSCN2154

I hope you find this blog useful.  Please feel free to add any comments or suggestions for improvement.

Advertisements